DescriptionPackage : SMDis_customized : YesModel Number : 5V 12V 1 Channel Relay ModuleOperating Temperature : -40-+85Dissipation Power : 1Supply Voltage : 5V/12VApplication : ComputerCondition : NewType : Voltage RegulatorBrand Name : EstardynOrigin : Mainland China1. Omron 5V solid state relay 240V 2A,the output with a resistive fuse 240V 2A.2. size: 1 way: 25 * 34 * 25 (long * wide * high) 2 way: 55 * 33 * 25 (long * wide * high) 4 way: 57 * 55 * 25 (long * wide * high) 8 Way: 106 * 56 * 25 (L * W * H)3. input power: 5V DC (160MA)4. the input control signal voltage:High level module: (0-2.5V state low level relay ON)(3.3-5V state high level relay OFF)Low level module: (0-2.5V state low level relay OFF)(3.3-5V state high level relay ON)5. there are 2.54CM pin and blue KF301 terminal control line is more convenient.Input section:DC +: Connect the power supply positive (according to the relay voltage)DC-: Connect the power supply negativeCH1: 1 relay module signal trigger terminal (low level trigger active)CH2: 2 relay module signal trigger terminal (low level trigger active)CH3: 2 relay module signal trigger terminal (low level trigger active)CH4: 2 relay module signal trigger terminal (low level trigger active)High and low meaning:High-level trigger refers to the signal trigger side (IN) and the negative power supply has a positive voltage between the positive and the power supply is usually connected to the trigger side of a trigger,when the trigger side voltage or trigger to reach the trigger Voltage,the relay is pull.Low-level trigger refers to the voltage between the signal trigger terminal and the negative terminal of the power supply is OV,or the voltage of the trigger terminal is lower than the voltage of the positive terminal of the power supply. When the voltage is low enough to trigger,the relay is pulled in,The negative side of the power supply is connected to the trigger side of a trigger,so that the relay is pull.Electrical parameters:Voltage Version Quiescent Current Operating Current Trigger Voltage Trigger Current1 channel 5V 0mA 12.5mA 0-2.5V 2mA2 5V 0mA 22.5mA 0-2.5V 2mA4 5V 0mA 48mA 0-2.5V 2mA4 5V 0mA 102mA 0-2.5V 2mAproduct manual:1. Module power supply: the power must be DC,the voltage and the relay voltage to match2. Wiring method:When the trigger side of the signal trigger level,the relay will be connected,the device has electricity and workPrecautions:1. Module power supply: power must be DC,5V power supply2. Module control terminal voltage: This module can only be used to control the AC current,can not control the DC current.Features:1.Dual trigger design,use a dedicated two-way driver IC.2.Strong resist interference,use diode continued current to protect it.3.The relay contact part adopts double cloth line for large current,safe and reliable.4.The input and output are 5.08mm wiring terminals,wiring is more convenient,suitable for PLC control.5.Input terminals can be arbitrarily set high and low level,the control mode is more flexible.6.Equipped with fixing screw hole,easy to install.7.Each way module can be set high or low triggered by jumper.Specifications:Material: MetalMounting bolts holes: 4Holes diameter: 3mmVoltage: 5V 12VMaximum load : AC 250V/10A,DC 30V/10AInterface:VCC: Power endGND: Ground strapCTR1-CTR8: Signal input triggerOutputs:24 line interface,the interface can be directly connected to all leads ,user-friendly.NO1-NO8: normally open relay interfaces ,relay before the vacant after the pull shorted with COMCOM1-COM8: Relay Common InterfaceNC1-NC8: normally closed relay interface relay shorted with COM ago ,after the pull- vacantProduct description:1 channel relay moduleMaximum load: AC 250V/10A,DC 30V/10ATrigger current: 5mAWorking voltage: 5VModule size: 50 x 26 x 18.5mm (L x W x H)Four mounting bolts holes,diameter 3.1mmDC+: positive power supply (VCC)DC-: negative power supply (GND)IN: can be high or low level control relayNO: normally open relay interfaceCOM: Common Interface RelaysNC: normally closed relay interface2 channel relay module1 Dimensions: 50.5mm (length) * 38.5mm (W) * 18.5 (H)2 Weight:. 31g3.PCB Color: Black4 board four weeks with four screws holes,hole diameter 3.1mm,easy to install and fixed5 relay of high quality loose music relays SPDT. A common terminal,a normally open,one normally closed terminal6 optocoupler isolation,good anti-jamming7 low pull,high release. Energisation status indicator light,release status LED is off8.VCC of system power,JD_VCC relay power. You can plug in jumpersElectrical parameters:Supply voltage: 5VDC,12VDCCurrent: more than 100mALoad: 250V 10A AC or 30V 10A DCWiring:VCC: positive power supply systemGND: System power negativeIN1 - IN2: relay control ports4-channelrelayoutput modules,relayoutput contacts250A 10A.InputIN1,IN2,IN3,IN4,the signal lineLOWeffective.VCC,GNDpower input,canrelaya