_x005F_x000D_ _x005F_x000D_ _x005F_x000D_ _x005F_x000D_ _x005F_x000D_ _x005F_x000D_ _x005F_x000D_ _x005F_x000D_ _x005F_x000D_ _x005F_x000D_ _x005F_x000D_ _x005F_x000D_ Specification:_x005F_x000D_ Material: ABS_x005F_x000D_ Type: AB, ON/OFF, Close Unlock_x005F_x000D_ Product size: 50*35*12mm/1.96*1.37*0.47''_x005F_x000D_ Rated voltage: 12 (V)_x005F_x000D_ Rated current: 10 (mA)_x005F_x000D_ Installation mode: wireless_x005F_x000D_ Corresponding frequency: 433MHZ _x005F_x000D_ Modulation mode: ASK (AM)_x005F_x000D_ Wireless transmission distance: 50-100m (open space)_x005F_x000D_ Application: garage door, alarm, automatic door, rolling door, etc_x005F_x000D_ Type of copied chip: 2260 (e.g. PT2260, SC2260, LX2260,HX2260); 2262, (such as PT2262, SC2262, LX2262,HS2262,HX2262, etc.), PT2264, PT2240 (LX2240), 1527(such as EV1527, HS1527, HX1527), FP527, CS5211, SMC918, SMC926, AX5026, ax5326-3, ax5326-4, HT600, HT680, HT6207, HT6010, HT6012, HT6013, HT6014, HT12D, HT46F49E, PIC16F629, PIC16F630, etc., can also copy other types of chips compatible with the above mentioned chips. Different chip manufacturers will have different prefix chip model, as long as the chip model number Part of the same can be copied_x005F_x000D_ Note: We generally do not recommend copying roll code chip, because there is a lot of uncertainty when copying roll code chip. When copying roll code chip remote control, we cannot determine whether the original remote control chip is an encryption chip or not, and we do not recommend copying roll code remote control with a pair of remote control._x005F_x000D_ _x005F_x000D_ Operation Manual:_x005F_x000D_ 1. Clean code: shut at the same time hold the lock with two keys (some of the shell are the two key) upward and downward, the LED indicator lights flashing three times, press release any one of the key, another is not loose, click the release button three times, rapid flashing LED light into the state, at this time of memory data all cleared, after cleaning the data of the remote control, press any key, the LED indicator is on._x005F_x000D_ 2. Copy: One hand-held original remote controller, the other hand-held copy remote controller, two remote controllers as close as possible, (ideally two remote controllers zero distance side by side on the desktop) respectively press the required copy buttons, LED indicator flickers quickly after three flickers, copy success, other key operation method is the same. Some remote controllers have low transmitting power, so they should be equipped with remote controllers and back-to-back operation of copying remote controllers to cope well. If there is interference in some operating environments, interference operation should be avoided. If copying is not good, copying should be done again after code clearance._x005F_x000D_ 3. Recovery: When you inadvertently clear the code of the copying remote controller, you can press the bottom two keys of the copying remote controller at the same time. After three flashes of the LED lamp, it will flicker quickly. After release, you press any key again and the light is long, which indicates that the code of the copying remote controller has been restored. Before using our copy remote control to copy, please make sure to clear the existing code of the copy remote control first._x005F_x000D_ _x005F_x000D_ 4. How to control some of the keys after copying, and the rest can not be controlLED, you can use the tips of cleaning and restoring operation, the specific operation is as follows:_x005F_x000D_ (1) Clearing the code first._x005F_x000D_ (2) Copy the keys that have not been copied successfully again after the successful code clearance, and do not copy the keys that have been copied successfully before._x005F_x000D_ (3) Clearing the code again._x005F_x000D_ (4) Make a restore operation once; at this time, the key that had not been successfully copied was covered by the copy code, while the original copy of the successful code was retained. If there are still keys that have not been copied successfully after the second copy, they can be coded again, and the keys that have not been copied successfully can be copied again, and then coded and restored again. This is repeated until all keys are successfully copied. This little trick can be used to reduce the hassle of repetitive operations._x005F_x000D_ _x005F_x000D_ Warm Tips:_x005F_x000D_ 1. Prerequisites for selecting the duplicate remote controller: the original remote controller has normal function, the remote control chip is the same or compatible, and the remote control work frequency is the same._x005F_x000D_ 2. The copying remote controller can only copy fixed code, learning code chip and remote controller of some single chip computers (the type of chip that can be copied is shown in the description of the type of chip that can be copied)._x005F_x000D_ 3. Two