Features： 1、PROGRAMMABLE FUNCTION: This offline sequence controller has programmable function, which can be customized to set up a great sequence trace according to actual requirements. 2、BASIC VALUES: This programmable offline sequence controller has an operating voltage of DC12 to 24V, a screen structure of 5 digits and a high brightness digital tube. 3、USE SCENARIO: Our programmable off line serial controller is widely applied in industrial automation control, small mechanical devices. 4、MADE OF PC MATERIAL: The programmable offline sequence controller is made of PC material, which is strong and durable. 5、LIGHT WEIGHT: Our programmable offline sequence controller is light weight and easy to install and very practical and helpful. Specification： Item Type: Programmable controller Material: PC Housing Size: Approx. 99.7 x 72 x 17mm / 3.93 x 2.83 x 0.67in (L x W x H) Screen Structure: 5 digit, high brightness digital tube Operating Environment: -5℃- 60℃ (no condensation) Opening Size: Approx. 92 x 69.8mm / 3.62 x 2.75in (L x W) Input: 5 programmable inputs, 2 fixed inputs Serial number Function Range Default value F0 Cycle working times Unit: times (demonstrated below)    0-65534, 65535 for countless times 1 F1 Number of rows at the beginning of the loop Unit: rows (Demonstrated below) 0-40 0 If the number of lines at the beginning of the loop > the number of lines at the end of the loop, it is illegal. Will alarm F2 Number of rows at the end of the loop Unit: rows (demonstrated below) 0-40 40 Illegal if the number of lines at the beginning of the loop > the number of lines at the end of the loop. Will alarm F3 Open [Output] manual debugging interface (restart to exit automatically or press [Return]) Introduced below 0 F4 Open [Input] manual debugging interface (restart to exit automatically or press [Return]) Introduced below 0 F5 Turn on programming mode (restart to exit automatically) 0-1 0 If you do not turn on the programming privileges, it is not possible to change the programming statements and alarm 0: Turn off programming privileges (power off automatically changes to 0)  1: Turn on programming privileges F15 Adjust the amplitude value of [overall working time] during operation  Unit:second 0-65535.999 , 0=no speed change during operation 0 F16 Auto run at power on specified program line: 31-40 lines 0-2 0 0 Turn off. If turned off, program segment 31-40 lines will automatically act as normal program category 1 Power on automatically runs program segment 31-40 lines.  2 The power on automatically works. F17 Action when ESC emergency stop key is pressed 0-2 0 0 Program ends and turns off all outputs    1 Program ends and holds current state 2 Program ends and runs program segment lines 31-40 If parameter 2 is not selected, then program lines 31-40 automatically act as normal program categories F18 Selectively switch P interface or F interface   0-3 0 1 Off [P interface] on [F interface]  2 On [P interface] off [F interface] 3 All off (temporary open: press [Set] key before power on)  0 All on F19 Main interface display content     0-2 0 0 Realtime working status. Display the total number of working times (not the number of cycles) under standby   1 Displays the number of cycles (not the total number)  2 Displays what line of program the system is running F20 Port filtering time of input port     0-65535 120 Set again when there is external interference. The higher the value, the slower the response Unit: Level F21 Start or emergency stop button signal filtering time on the panel   0-65535 27 Set again when there is external interference. The higher the value, the slower the response Unit: Level F24 Restore the factory setting     0-4 4 Note: After changing this parameter, you need to power off and restart 1 Restore [F] parameter only  2 Restore [P] parameter only 3 Restore all  4 No need to restore    0 or >10: restore all and open self test mode, factory mode (only for factory use) Package List： 1 x Programmable Controller