DSO138 Oscilloscope Digital Assembled TFT with Probe Alligator Test Clip for Arduino ARM Detection D 25-26

33,95 €
la livraison GRATUITE

DSO138 Oscilloscope Digital Assembled TFT with Probe Alligator Test Clip for Arduino ARM Detection D 25-26

  • Marque: Unbranded
Verkocht door:

DSO138 Oscilloscope Digital Assembled TFT with Probe Alligator Test Clip for Arduino ARM Detection D 25-26

  • Marque: Unbranded

33,95 €

Économisez 25,05 € (42%)

Prix de vente recommandé

59,00 €
En stock
la livraison GRATUITE
Verkocht door:

33,95 €

Économisez 25,05 € (42%)

Prix de vente recommandé

59,00 €
En stock
la livraison GRATUITE

Nous acceptons les modes de paiement suivants

Description

DSO138 Oscilloscope Digital Assembled TFT with Probe Alligator Test Clip for Arduino ARM Detection D 25-26

This kit uses ARM Cortex-M3 processor (STM32F103C8), and includes a 2.4-inch color TFT display screen, can be used as ARM test development board. Can be secondary development on the basis of this kit, for example, it can be changed to Millivoltmeter, With automatic, regular and one-shot modes, easy to capture the moment waveform. Comes 1Hz or 3.3V square wave test signal source. With waveform parameter digital display, including frequency, period, pulse width, duty ratio, MAX. or MIN. or AVG. or Peak- Maximum real-time sampling rate: 1Msps Accuracy: 12Bit Sample buffer depth: 1024 bytes Analog Bandwidth: 0 - 200KHz Vertical Sensitivity: 10mV or Div - 5V or Div (in 1-2-5 increments) Adjustable vertical displacement with indication Input impedance: 1MΩ Maximum input voltage: 50Vpp (1:1 probe), 400Vpp (10:1 probe) Coupling methods include DC or AC or GND Horizontal time base range: 10μs or Div - 50s or Div (in 1-2-5 increments) With automatic, conventional and single trigger modes, it is convenient to capture instantaneous waveforms Trigger with rising or falling edge Adjustable trigger level position with indication Waveform before trigger can be observed (negative delay) Waveform display can be freeze at any time (HOLD function) Comes with 1KHz or 3.3V square wave test signal source Digital display with waveform parameters, the parameters that can be displayed are: frequency, period, pulse width, duty cycle, maximum value, minimum value, average value, peak-to-peak value, RMS Save or recall the waveform, the waveform does not disappear when power off Colour:Red Material:ABS Size:18 x 12.5 x 3cm Package Contents: 1 x DSO138 DIY Digital Oscilloscope Kit 1 x Probe Only the above package content, other products are not included. Note: Light shooting and different displays may cause the color of the item in the picture a little different f Note: Due to the light and screen setting difference, the item's color may be slightly different from the pictures. Please allow slight dimension difference due to different manual measurement.
  • Identifiant Fruugo: 445967718-936504096
  • EAN: 7438599604249

Livraison & retours

Expédition dans un délai de 2 jours

  • STANDARD: GRATUIT - Livraison entre lun. 22 décembre 2025–lun. 29 décembre 2025 - GRATUIT

Expédition de Chine.

Nous mettons tout en œuvre pour que les produits que vous commandez vous soient livrés dans leur intégralité et selon vos indications. Néanmoins, si vous recevez une commande incomplète, des articles différents de ceux commandés ou si, pour toute autre raison, la commande ne vous satisfait pas, vous pouvez retourner la commande ou tout produit inclus dans celle-ci et recevoir un remboursement complet des articles. Voir l'intégralité de la politique de retour

Détails de conformité du produit

Veuillez consulter les informations de conformité spécifiques à ce produit décrites ci-dessous.

Les informations suivantes sont fournies par le détaillant tiers indépendant vendant ce produit.

Fabricant:
Les informations suivantes indiquent les coordonnées du fabricant du produit concerné vendu sur Fruugo.

  • Hefei Zheshuo Technology Co., Ltd.
  • Hefei Zheshuo Technology Co., Ltd.
  • Hefei City, Anhui Province, Shushan District, Anhui Province, No. 15, South Seventh Street, South Cooperative South Road, Chemical Machinery Community, Building 1, Unit 2, 603
  • Hefei
  • CN
  • 523011
  • nacufalacan81@hotmail.com
  • 13243801962

Personne responsable dans l'UE:
Les informations suivantes indiquent les coordonnées de la personne responsable dans l'UE. La personne responsable est l'opérateur économique désigné basé dans l'UE qui est responsable des obligations de conformité relatives au produit concerné vendu dans l'Union européenne.

  • Jean Luc
  • In Memoria Futuri SAS
  • 3 RUE DU PAS DE LA MULE 75004 PARIS
  • Paris
  • France
  • 75004
  • infoapexchen@gmail.com
  • 33745713901